国产第6页-国产第9页-国产第九页-国产第六页-国产第三区-国产第十页

Welcome To Wuxi Yi Rui Machinery Co., Ltd. 中文 CN  英文 EN
Yi Rui Would Be Your Friend Forever, And You Work Together!
TEL:0510-83691239
Yi Rui Product List
Wuxi Yi Rui Machinery Co., Ltd.
Contact: Yu Haibo (0) 13861855788
Tel: 0510-83691239
Fax: 0510-83690239
Postal Code: 214155
Email: sales@wx-yr.com
Q Q: 451055015
Address: Yang Shan Town, Wuxi
NEWS INFORMATION
Position:Home > NEWS >

Repair of hydraulic cylinder piston rod

After the hydraulic cylinder piston rod strain, if you do not promptly treated, ranging from affecting the normal use, while the hydraulic cylinder is not working. Our repair method is that for lighter pull marks take partial grinding method of polishing repair; for heavier pull marks the take welding method plus artificial grinding repair.

Pull scar formation: after the disintegration of the crane, a fluffing cylinder piston rod was found to be severely strained, pulled alongside six marks. The main cause is the piston rod strain: dust ring was brittle after massive loss, not only lost the role of dust, but were also piled up a lot of dust and magazines, the piston rod directly with impurity hard grind, cause the piston lever is pulled, the scars Zaigua bad hatch rubber seal components, resulting in serious leakage of hydraulic cylinders.

Repair requirements: filler and base metal must be combined with a solid, smooth; seasoning must be durable and easy to manual processing; manual processing must ensure that the piston rod diameter error is less than 0.06mm. After analysis, the decision to adopt the filler is J422 electrode. Because, acid electrode of rust, oil and water is not sensitive, not prone to hydrogenation hole; technology is good, easy to operate; weld appearance; moderate hardness, easy to manual processing; arc stability, penetration larger, and the base material combined firm.
Repair process:
(1) The first parts to be welded cleaned with wet mud and then will pull marks four weeks surrounded.
(2) Selection of 2.5mm diameter rod, the welding current is adjusted to 120A; take a smooth linear motion welding strip method.
(3) After all the welding complete, the mud and slag cleaned with rasps are repaired along the circumference of the piston rod and leave 0.1-0.2mm filing allowance.
(4) a vehicle outside diameter of 185mm, an inner diameter of 125mm, 150mm long when the cam cylinder (piston rod diameters 125mm), along the axis of sawing, a coarse mode, the other for the fine mode.
(5) in the inner wall of the mold coated with a thin layer of coarse red ink, then the crude mold abuts on the piston rod parts for repairs along the axis of the run several times back and forth, and then with a fine file heavier red marks on the piston rod file out. Again revised filing, and after leaving 0.04-0.07mm allowance.
(6) The purpose of the sand bar 320 and then dipped in kerosene piston rod with precision molding grinding to a predetermined size.
(7) Finally, the back of the hand-polished emery cloth dipped in kerosene. After the measurement, the maximum error is only 0.03mm.
After the crane repair, after a year and a half of use, fluffing cylinder leakage phenomenon has not occurred, while the rod is smooth, no rust.
 
Website ©2015 Wuxi Yi Rui Machinery Co., Ltd. Copyright ALL RIGHTS RESERVED
Contact: Yu Haibo (0) 13861855788 Tel: 0510-83691239 Fax: 0510-83690239 Postal Code: 214155 Email: sales@wx-yr.com Q Q: 451055015 Address: Yang Shan Town, Wuxi

Sweep

Concern

主站蜘蛛池模板: 亚洲精品影院一区二区 | 97精品国产综合久久久久久欧美 | 日韩精品首页 | 在线免费观看一区二区三区 | 亚洲视频在线观看地址 | 日日操夜夜操免费视频 | 国产精品一区二 | 黄页网站 播放器 日本 | 成人午夜在线视频 | 亚洲一区在线免费观看 | 久久激情综合色丁香 | 成年午夜视频免费观看视频 | 欧美在线成人午夜网站 | 理论片我不卡在线观看 | 国产精品欧美亚洲韩国日本久久 | 免费福利视频网站 | 国产一起色一起爱 | 色爱b| 成人免费观看一区二区 | 热久久国产 | 亚洲字幕| 精品小视频在线 | 成人sese| 欧美一级毛片免费高清的 | 久久久香蕉 | 老司机午夜影院 | 久久天天躁狠狠躁狠狠躁 | 欧美 国产 日本 | 91在线播放视频 | 欧美性生活视频免费 | 97人人在线观看 | 国产精品久久久久久一级毛片 | 亚洲日韩色综合视频 | 日韩精品欧美一区二区三区 | 九九精| 亚洲另类视频 | 视频在线观看入口一二三2021 | 国产欧美一区二区精品久久久 | 真91视频| 久久国产综合精品欧美 | 亚洲欧美视频一区二区三区 |